Software Vault: The Gold Collection

home *** CD-ROM | disk | FTP | other *** search

/ Software Vault: The Gold Collection / Software Vault - The Gold Collection (American Databankers) (1993).ISO / cdr11 / ibmlist.zip / PS2ERROR.LST < prev next >

Wrap

File List | 1990-12-05 | 43KB | 815 lines

TITLE: 1XX SYSTEM BOARD ERRORS.............................1001 101 POST Error - Interrupt failure. 102 POST Error - Timer failure. 102 DIAGS Error - Real time clock 64 byte CMOS RAM TEST 103 POST Error - Timer interrupt failure. 103 DIAGS Error - 2KB CMOS RAM TEST 103 (PS2TAPE - Insufficient memory for program to load) 104 POST Error - Protect Mode Failure 104 DIAGS Error - Real time clock timing test 105 POST Error - Last 8042 command not accepted. 106 POST Error - Converting logic test. 107 POST Error - Hot NMI test. 108 POST Error - Timer bus test. 109 POST Error - Low meg CHIP SELECT test 109 DMA or arbitration error (8550 & 8560 only) 110 POST Error - Planar PARITY 111 POST Error - I/O PARITY 111 DIAGS Error - Test Protect Mode (80286 type protect mode test) 112 POST Error - Watchdog timeout 112 DIAGS Error - Test 80386 New and Extended Registers 113 POST Error - DMA arbitration timeout 113 DIAGS Error - Test 80386 New Instructions 114 POST Error - External ROM checksum error 114 DIAGS Error - Test 80386 32-bit Adressing Modem 115 DIAGS Error - Test 80386 Protect Mode 116 DIAGS Error - Test 80386 16/32 bit (mult., div., sub., add) 118 POST Error - Logged memory error - run Adv Diags (90 & 95) 120 POST Error - processor self test failed 121 DIAGS Error - Test Hot reset of processor (via port 90H) 131 DIAGS Error - Test DMA Compatibility Registers 132 DIAGS Error - Test DMA Extended Registers 133 DIAGS Error - Test DMA Verify Logic 134 DIAGS Error - Test Arbitration Logic 152 DIAGS Error - Real Time Clock Failure (or CMOS RAM ERROR) - 152 invalid error if using V1.0 Reference Diskette. 160 POST Error - Planar ID not recognized 161 POST Error - System options not set - (Run SETUP) - battery failure 162 POST Error - System options not set - (Run SETUP) 163 POST Error - Time and date not set- (Run SETUP). 164 POST Error - Memory error - (Run SETUP if memory added or deleted) 165 POST Error - System options not set - (Run SETUP) - card ID mismatch 166 POST Error - Card busy error 167 POST Error - Clock not updating 169 POST Error - Planar/processor card mismatch (Run SETUP) 170 POST Error - ASCII setup conflict 171 DIAGS Error - Failed I/O addressing test 173 POST Error - CMOS checksum error (Run SETUP) 174 POST Error - Bad configuration (Run SETUP) 191 DIAGS Error - Failed 82385 cache test ~~~~~ TITLE: 2XX MEMORY ERRORS...................................1002 201 POST Error - Memory error 201 DIAGS Error - data miscompare or parity or adapter ** MORE INFO ** 202 POST Error - Memory address error 202 DIAGS Error - Address error 203 POST Error - Memory address error 203 DIAGS Error - Refresh failure 204 DIAGS Error - Relocated memory (run Diagnostics again) 205 DIAGS Error - CMOS ERROR 207 DIAGS Error - ROM ERROR 210 POST Error - Parity error in base 64K 211 POST Error - Base 64K on I/O channel failed 215 POST Error - Base 64K on daughter card #2 failed 216 POST Error - Base 64K on daughter card #1 failed 221 POST Error - ROM or RAM copy error (8570 only) 225 POST Error - Wrong Memory Speed (8570 only) ~~~~~ TITLE: 3XX KEYBOARD ERRORS.................................1003 301 POST Error - Keyboard error 301 DIAGS Error - Replace keyboard 302 DIAGS Error - User indicated error 303 POST Error - Keyboard or System Board error 303 DIAGS Error - System Board failure 304 POST Error - System Board error 305 POST Error - Keyboard +5v error ~~~~~ TITLE: 4XX PARALLEL PORT ERRORS............................1004 401 POST Error - Parallel Port error 401 DIAGS Error - Parallel Port error callout System Board ~~~~~ TITLE: 6XX DISKETTE DRIVE OR DRIVE CONTROLLER ERRORS......1005 601 POST Error - Diskette drive or Controller error 602 POST Error - Diskette boot record error 630 DIAGS Error - Index stuck high (replace Drive "A") 631 DIAGS Error - Index stuck low (replace Drive "A") 632 DIAGS Error - Track 0 stuck off (replace Drive "A") 633 DIAGS Error - Track 0 stuck on (replace Drive "A") 640 DIAGS Error - Index stuck high (replace Drive "B") 641 DIAGS Error - Index stuck low (replace Drive "B") 642 DIAGS Error - Track 0 stuck off (replace Drive "B") 643 DIAGS Error - Track 0 stuck on (replace Drive "B") 650 DIAGS Error - Drive speed error (replace drive being tested) 651 DIAGS Error - Format failure (replace drive being tested) 652 DIAGS Error - Verify failure (replace drive being tested) 653 DIAGS Error - Read failure (replace drive being tested) 654 DIAGS Error - Write failure (replace drive being tested) 655 DIAGS Error - Controller error (replace planar) 656 DIAGS Error - Drive failure (replace drive being tested) 657 DIAGS Error - Write protect stuck protected (replace failing drive) 658 DIAGS Error - Change line stuck changed (replace failing drive) 659 DIAGS Error - Write protect stuck unprotected (replace failing drive) 660 DIAGS Error - Change line stuck unchanged (replace failing drive) ~~~~~ TITLE: 7XX MATH COPROCESSOR ERRORS.........................1006 701 POST Error - Math Coprocessor Error 701 DIAGS Error - Math Coprocessor Presence Initialization 702 DIAGS Error - Exception errors test 703 DIAGS Error - Rounding test 704 DIAGS Error - Arithmetic test 1 705 DIAGS Error - Arithmetic test 2 706 DIAGS Error - Arithmetic test 3 (only for 80387) 707 DIAGS Error - Combination test 708 DIAGS Error - Integer load/store 709 DIAGS Error - Equivalent expressions 710 DIAGS Error - Exception (interrupts) 711 DIAGS Error - Save state (FSAVE) 712 DIAGS Error - Protected mode (protected mode) 713 DIAGS Error - Special test may catch voltage/temp problems ~~~~~ TITLE: 11XX ASYNC (SERIAL PORT) ERRORS.....................1007 1101 POST Error - 16550 async chip error 1102 DIAGS Error - Card selected feedback error 1103 DIAGS Error - Port 102H fails register test 1106 DIAGS Error - Serial option cannot be put to sleep 1107 DIAGS Error - Cable error 1108 DIAGS Error - Async IRQ3 Error 1109 DIAGS Error - Async IRQ4 Error 1110 DIAGS Error - 16550 fails register test 1111 DIAGS Error - Internal wrap test of 16550 modem control lines failed 1112 DIAGS Error - External wrap test of 16550 modem control lines failed 1113 DIAGS Error - 16550 transmit error 1114 DIAGS Error - 16550 receive error 1115 DIAGS Error - 16550 receive data not equal transmit data 1116 DIAGS Error - 16550 interrupt function error 1117 DIAGS Error - 16550 failed baud rate test 1118 DIAGS Error - 16550 interrupt driven receive wrap test failed 1119 DIAGS Error - 16550 FIFO error ~~~~~ TITLE: 12XX DUAL ASYNC ADAPTER ERRORS......................1008 1201 DIAGS Error - Cannot detect presence of dual async adapter 1202 DIAGS Error - Card selected feedback error 1203 DIAGS Error - Port 102H failed register test 1206 DIAGS Error - Serial option cannot be put to sleep 1207 DIAGS Error - Cable error 1208 DIAGS Error - Async IRQ3 Error 1209 DIAGS Error - Async IRQ4 Error 1210 DIAGS Error - 16550 fails register test 1211 DIAGS Error - Internal wrap test of 16550 modem control lines failed 1212 DIAGS Error - External wrap test of 16550 modem control lines failed 1213 DIAGS Error - 16550 transmit error 1214 DIAGS Error - 16550 receive error 1215 DIAGS Error - 16550 receive data not equal transmit data 1216 DIAGS Error - 16550 interrupt function error 1217 DIAGS Error - 16550 failed baud rate test 1218 DIAGS Error - 16550 interrupt driven receive wrap test failed 1219 DIAGS Error - 16550 FIFO error 1225 DIAGS Error - 16550 fails register test 1226 DIAGS Error - Internal wrap test of 16550 modem control lines failed 1227 DIAGS Error - External wrap test of 16550 modem control lines failed 1228 DIAGS Error - 16550 transmit error 1229 DIAGS Error - 16550 receive error 1230 DIAGS Error - 16550 receive data not equal transmit data 1231 DIAGS Error - 16550 interrupt function error 1232 DIAGS Error - 16550 failed baud rate test 1233 DIAGS Error - 16550 interrupt driven receive wrap test failed 1234 DIAGS Error - 16550 FIFO error ~~~~~ TITLE: 14XX PRINTER ERRORS.................................1009 1401 DIAGS Error - Printer failure 1402 DIAGS Error - Out of paper 1403 DIAGS Error - Interrupt failure 1404 DIAGS Error - System Board timeout 1405 DIAGS Error - Parallel adapter 1406 DIAGS Error - Presence test failed ~~~~~ TITLE: 16XX 36/38 ADAPTER ERRORS ..........................1010 ~~~~~ TITLE: 17XX FIXED DISK DRIVE AND ADAPTER ERRORS (ST506)....1011 1701 POST Error - Fixed Disk and/or Adapter failure 1750 DIAGS Error - Verify failure - drive failure 1751 DIAGS Error - Read failure - drive failure 1752 DIAGS Error - Write failure - drive failure 1753 DIAGS Error - RND READ test failure - drive failure 1754 DIAGS Error - Seek test error - drive failure 1755 DIAGS Error - Controller failure 1756 DIAGS Error - ECC test failure - controller failure 1757 DIAGS Error - Head select failure - controller failure 1780 POST Error - Disk 0 failure 1781 POST Error - Disk 1 failure 1782 POST Error - Disk Controller failure 1782 POST Error - System Board configuration Problem (repl. System Board) 1790 POST Error - Disk 0 failure 1791 POST Error - Disk 1 failure ~~~~~ TITLE: 24XX PLANAR VGA VIDEO ERRORS........................1012 2401 POST Error - Planar video error 2402 DIAGS Error - Planar video Error 2409 DIAGS Error - Replace Display 2410 DIAGS Error - Replace System Board ~~~~~ TITLE: 28XX 3270 CONNECTION ADAPTER ERRORS.................1013 2801 POST Error - 3270 Adapter. 2801 DIAGS Error - KEYSTROKE ACCEPTED STATUS BIT FAILURE 2802 DIAGS Error - RESET DECODED STATUS BIT FAILURE 2803 DIAGS Error - CURSOR LOW REG INCORRECT ON RESET 2804 DIAGS Error - CURSOR HIGH REG INCORRECT ON RESET 2805 DIAGS Error - RAM BUFFER RIPPLE PATTERN INCORRECT ON RESET 2806 DIAGS Error - NO POR STATUS ON POLL AFTER RESET 2807 DIAGS Error - STATUS NOT CLEAR ON POLL ACK 2808 DIAGS Error - TERMINAL ID REG WRITE/READ TEST FAILED 2809 DIAGS Error - NOT BUSY STATUS BIT NOT WORKING 2810 DIAGS Error - ADDRESS COUNTER LOW INCORRECT 2811 DIAGS Error - CURSOR LOW REG INCORRECT 2812 DIAGS Error - ADDRESS COUNTER HIGH INCORRECT 2813 DIAGS Error - CURSOR HIGH REG INCORRECT 2814 DIAGS Error - BUFFER BEING MODIFIED BIT OFF DURING WRITE COMMAND 2815 DIAGS Error - BASE BUFFER MODIFIED COMPLETE NOT SET BY WRITE COMMAND 2816 DIAGS Error - WRITE COMMAND/READ COMMAND RESULTS NOT COMPARING 2817 DIAGS Error - BUFFER BEING MODIFIED OFF DURING CLEAR COMMAND 2818 DIAGS Error - BASE BUFFER MODIFIED COMPLETE NOT SET BY CLEAR COMMAND 2819 DIAGS Error - NO OP COMPLETE STATUS AFTER CLEAR COMMAND 2820 DIAGS Error - WRONG AREA CLEARED BY CLEAR COMMAND 2821 DIAGS Error - CORRECT AREA NOT CLEARED BY CLEAR COMMAND 2822 DIAGS Error - CORRECT AREA NOT CLEARED BY CLEAR COMMAND 2823 DIAGS Error - STOPPING ADDRESS NOT CORRECT AFTER CLEAR COMMAND 2824 DIAGS Error - STOPPING ADDRESS NOT CORRECT AFTER CLEAR COMMAND 2825 DIAGS Error - CORRECT AREA NOT CLEARED BY CLEAR COMMAND 2826 DIAGS Error - WRONG AREA CLEARED BY CLEAR COMMAND 2827 DIAGS Error - STOPPING ADDRESS NOT CORRECT AFTER CLEAR COMMAND 2828 DIAGS Error - STOPPING ADDRESS NOT CORRECT AFTER CLEAR COMMAND 2829 DIAGS Error - CORRECT AREA NOT CLEARED BY CLEAR COMMAND 2830 DIAGS Error - WRONG AREA CLEARED BY CLEAR COMMAND 2831 DIAGS Error - BUFFER BEING MODIFIED OFF DURING INSERT COMMAND 2832 DIAGS Error - BASE BUFFER MODIFIED COMPLETE NOT SET BY INSERT COMMAN 2833 DIAGS Error - NO OP COMPLETE STATUS AFTER INSERT COMMAND 2834 DIAGS Error - WRONG DATA DISTURBED BY INSERT COMMAND 2835 DIAGS Error - BYTE INSERTED AT WRONG ADDRESS BY INSERT COMMAND 2836 DIAGS Error - DATA SHIFTED INCORRECTLY BY INSERT COMMAND 2837 DIAGS Error - SHIFTING NOT STOPPED BY NULL DURING INSERT COMMAND 2838 DIAGS Error - BYTE AT WRONG ADDRESS AFTER INSERT COMMAND 2839 DIAGS Error - DATA SHIFTED INCORRECTLY BY INSERT COMMAND 2840 DIAGS Error - SHIFTING NOT STOPPED BY ATTRIBUTE ON INSERT COMMAND 2841 DIAGS Error - ADDRESS COUNTER NOT CORRECT AFTER SEARCH FORWARD COMMA 2842 DIAGS Error - CURSOR REG INCORRECT AFTER SEARCH FORWARD COMMAND 2843 DIAGS Error - NO OP COMPLETE STATUS AFTER SEARCH FORWARD COMMAND 2844 DIAGS Error - ADDRESS COUNTER NOT CORRECT AFTER SEARCH FORWARD COMMA 2845 DIAGS Error - CURSOR REG INCORRECT AFTER SEARCH FORWARD COMMAND 2846 DIAGS Error - ADDRESS COUNTER NOT CORRECT AFTER SEARCH BACKWARD COMM 2847 DIAGS Error - CURSOR REG INCORRECT AFTER SEARCH BACKWARD COMMAND 2848 DIAGS Error - NO OP COMPLETE AFTER SEACH BACKWARD COMMAND 2849 DIAGS Error - ADDRESS COUNTER INCORRECT AFTER SEARCH BACKWARD COMMAN 2850 DIAGS Error - CURSOR REG INCORRECT AFTER SEARCH BACKWARD COMMAND 2851 DIAGS Error - LOAD CONTROL REG COMMAND NOT CLEARING VISUAL/SOUND REG 2852 DIAGS Error - LOAD CONTROL REG COMMAND NOT SETTING VISUAL/SOUND REG 2853 DIAGS Error - INHIBIT FEATURE STEP NOT SETTING IN VISUAL/SOUND REG 2854 DIAGS Error - INHIBIT DISPLAY NOT SETTING IN VISUAL/SOUND REG 2855 DIAGS Error - INHIBIT CURSOR NOT SETTING IN VISUAL/SOUND REG 2856 DIAGS Error - REVERSE CURSOR NOT SETTING IN VISUAL/SOUND REG 2857 DIAGS Error - BLINK CURSOR NOT SETTING IN VISUAL/SOUND REG 2858 DIAGS Error - WRITE/READ OF PC/IL CONTROL REG INCORRECT 2859 DIAGS Error - ADAPTER DOES NOT CAUSE INTERRUPT WHEN ENABLED 2860 DIAGS Error - WRITE/READ TESTING OF RAM BUFFER FAILED 2861 DIAGS Error - POLLING DOES NOT CLEAR STATUS REG 2862 DIAGS Error - INTERRUPT/STATUS REG NOT CLEARING ON RESET UDER MASK 2863 DIAGS Error - SPARE COMMAND CAUSING UNEXPECTED ACTION 2864 DIAGS Error - NOT USED 2865 DIAGS Error - PAGE REGISTER FAILURE 2866 DIAGS Error - READ MULTIPLE COMMAND FAILURE 2867 DIAGS Error - 2868 DIAGS Error - 3287 MODE FAILURE 2869 DIAGS Error - TCA MODE FAILURE ~~~~~ TITLE: 46XX MULTIPORT/A ADAPTER ERRORS.....................1014 4611 Multiport Interface Card 4612 Multiport Memory Module 4613 Multiport Memory Module 4630 Multiport Interface Card 4640 Multiport Memory Module 4650 Multiport Interface Cable ~~~~~ TITLE: 56XX 4700PC FINANCIAL ADAPTER ERRORS................1015 5601 PS/2 keyboard failed. 5602 PS/2 Keyboard failed Self-Test. 5603 PS/2 Keyboard error. 5604 50-Key keyboard is not attached. 5605 50-Key keyboard self-test failed. 5606 50 Key keyboard error. 5607 Invalid keyboard configuration. 5608 50-Key keyboard parameter error. 5609 Invalid system for the keyboard program. 5611 PIN Keypad failed. 5614 No PIN Keypad attached to System Unit. 5615 PIN Keypad driver has an input parameter error. 5616 PIN Keypad not attached to the Pointing Device connector. 5617 Pin Keypad failed self-test. 5618 Pin Keypad has a communications error. 5619 System invalid for PIN keypad driver. 5621 Magnetic Stripe Unit failed. 5623 Magnetic Stripe Unit not connected to System Unit. 5624 Magnetic Stripe Unit driver input error. 5626 Magnetic Stripe Unit not attached to Pointing Device connector. 5627 Magnetic Stripe Unit self-test failed 5629 System invalid for the Magnetic Stripe Unit driver. 5630 STATUS = F1 system attempted unsucessful IPL from diskette. 5631 STATUS REMOTE START - normal start-up message. 5633 STATUS REMOTE IPL - normal start-up message. 5691 Device driver error. ~~~~~ TITLE: 62XX STORE LOOP ADAPTER ERRORS .....................1016 6201 POST ERROR - Replace Adapter 6210 DIAGS ERROR - Replace Adapter 6211 DIAGS ERROR - Replace Adapter 6212 DIAGS ERROR - Replace Adapter 6213 DIAGS ERROR - Replace Adapter 6214 DIAGS ERROR - Replace Adapter 6215 DIAGS ERROR - Replace Adapter 6216 DIAGS ERROR - Replace Adapter 6217 DIAGS ERROR - Replace Adapter 6218 DIAGS ERROR - Replace Adapter 6221 DIAGS ERROR - 8051 POR Error Check Status 6222 DIAGS ERROR - 8051 POR Error Check Status 6223 DIAGS ERROR - 8051 POR Error Check Status 6224 DIAGS ERROR - 8051 POR Error Check Status 6225 DIAGS ERROR - 8051 POR Error Check Status 6226 DIAGS ERROR - 8051 POR Error Check Status 6227 DIAGS ERROR - 8051 POR Error Check Status 6228 DIAGS ERROR - 8051 POR Error Check Status 6231 DIAGS ERROR - Latch Test Errors Check Status 6232 DIAGS ERROR - Latch Test Errors Check Status 6233 DIAGS ERROR - Latch Test Errors Check Status 6234 DIAGS ERROR - Latch Test Errors Check Status 6235 DIAGS ERROR - Latch Test Errors Check Status 6236 DIAGS ERROR - Latch Test Errors Check Status 6237 DIAGS ERROR - Latch Test Errors Check Status 6238 DIAGS ERROR - Latch Test Errors Check Status 6241 DIAGS ERROR - Shared Buffer Error Check Status 6242 DIAGS ERROR - Shared Buffer Error Check Status 6243 DIAGS ERROR - Shared Buffer Error Check Status 6244 DIAGS ERROR - Shared Buffer Error Check Status 6245 DIAGS ERROR - Shared Buffer Error Check Status 6246 DIAGS ERROR - Shared Buffer Error Check Status 6247 DIAGS ERROR - Shared Buffer Error Check Status 6248 DIAGS ERROR - Shared Buffer Error Check Status 6251 DIAGS ERROR - CMOS TEST Error Check Status 6252 DIAGS ERROR - CMOS TEST Error Check Status 6253 DIAGS ERROR - CMOS TEST Error Check Status 6254 DIAGS ERROR - CMOS TEST Error Check Status 6255 DIAGS ERROR - CMOS TEST Error Check Status 6256 DIAGS ERROR - CMOS TEST Error Check Status 6257 DIAGS ERROR - CMOS TEST Error Check Status 6258 DIAGS ERROR - CMOS TEST Error Check Status 6261 DIAGS ERROR - Dump Latch Error Check Status 6262 DIAGS ERROR - Dump Latch Error Check Status 6263 DIAGS ERROR - Dump Latch Error Check Status 6264 DIAGS ERROR - Dump Latch Error Check Status 6265 DIAGS ERROR - Dump Latch Error Check Status 6266 DIAGS ERROR - Dump Latch Error Check Status 6267 DIAGS ERROR - Dump Latch Error Check Status 6268 DIAGS ERROR - Dump Latch Error Check Status 6270 DIAGS ERROR - Cable or Adapter Error 6280 DIAGS ERROR - Dump switch not Operated in time 6290 DIAGS ERROR - NO Store loop adapter Present (Check Install List). ~~~~~ TITLE: 74XX 8514/A ADAPTER ERRORS..........................1017 7421 Replace the 8514/A Adapter 7422 Replace the 8514/A Adapter 7423 Replace the 8514/A Adapter 7424 Replace the 8514/A Adapter 7425 Replace the 8514/A Adapter 7426 Replace the 8514/A Adapter 7427 Replace the 8514/A Adapter 7435 Jumper on auxiliary storage card incorrect 7440 Module 31 defective 7441 Module 30 defective 7442 Module 29 defective 7443 Module 28 defective 7444 Module 22 defective 7445 Module 21 defective 7446 Module 18 defective 7447 Module 17 defective 7448 Module 32 defective 7449 Module 14 defective 7450 Module 13 defective 7451 Module 12 defective 7452 Module 06 defective 7453 Module 05 defective 7454 Module 02 defective 7455 Module 01 defective 7458 Replace the 8514/A Adapter 7460 Module 16 defective 7461 Module 27 defective 7462 Module 26 defective 7463 Module 26 defective 7464 Module 24 defective 7465 Module 23 defective 7466 Module 20 defective 7467 Module 19 defective 7468 Module 15 defective 7469 Module 11 defective 7470 Module 10 defective 7471 Module 09 defective 7472 Module 08 defective 7473 Module 07 defective 7474 Module 04 defective 7475 Module 03 defective 7478 Replace the 8514/A Adapter ~~~~~ TITLE: 76XX PERSONAL PAGEPRINTER ERRORS....................1018 76XX ~~~~~ TITLE: 78XX HIGH SPEED ADAPTER ERRORS .....................1019 7801 POST Error Replace High Speed Adapter ~~~~~~ TITLE: 79XX 3117 SCANNER AND ADAPTER ERRORS ...............1020 7901 3117 Adapter Error Replace Adapter 7902 3117 Scanner Error goto 3117 Scanner maps 7903 3117 Scanner cable error check or replace cable ~~~~~~ TITLE: 86XX MOUSE ERRORS...................................1021 8601 POST Error - System Board (Mouse Port) 8601 DIAGS Error - Replace Mouse 8602 POST Error - Mouse 8602 DIAGS Error - User indicated error 8603 POST Error - System Board or Mouse 8603 DIAGS Error - System Board failure 8604 DIAGS Error - System Board or Mouse failure ~~~~~~ TITLE: 91XX 3363 OPTICAL DISK DRIVE ERRORS.................1022 9101 OPTICAL DISK POST ERROR - Drive #1 failed - Reseat Cables and Adapter 9102 OPTICAL DISK POST ERROR - Drive #1 failed - Reinsert Cartridge 9102 - Reseat Adapter 9103 OPTICAL DISK POST ERROR - Drive #1 failed - Reseat Cables and Adapter 9104 OPTICAL DISK POST ERROR - Drive #2 failed - Reseat Cables and Adapter 9105 OPTICAL DISK POST ERROR - Drive #2 failed - Reinsert cartridge 9105 - Reseat cables and Adapter 9106 OPTICAL DISK POST ERROR - Drive #2 failed - Reseat cables and Adapter 9107 OPTICAL DISK POST ERROR - Adapter hung on BUSY - Reseat Cables and Adapter 9110 OPTICAL DISK DIAGS ERROR - Data not recorded - Check Adapter, Drive, Cable 9111 OPTICAL DISK DIAGS ERROR - Data not readable - Check Adapter, Drive, Cable 9112 OPTICAL DISK DIAGS ERROR - Sector demarked - Check Adapter, Drive, Cable 9113 OPTICAL DISK DIAGS ERROR - Controller Error - Check Adapter, Drive, Cable 9113 - Check switch settings 9113 on Adapter DS302 9113 (8088 vs 80286) 9114 OPTICAL DISK DIAGS ERROR - Sector Read/Write Error - Check Drive, Adapter 9114 - Check Cable 9115 OPTICAL DISK DIAGS ERROR - Scramble Buffer Error - Check Drive, Adapter 9115 - Check Cable 9116 OPTICAL DISK DIAGS ERROR - Data Buffer Error - Check Drive, Adapter 9116 - Check Cable 9117 OPTICAL DISK DIAGS ERROR - Drive RAM/ROM Error - Check Drive, Adapter 9117 - Check Cable 9118 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Drive, Adapter, Cable 9119 OPTICAL DISK DIAGS ERROR - Track Jump Error - Check Drive, Adapter, Cable 9120 OPTICAL DISK DIAGS ERROR - Laser Error - Check Drive, Adapter, or Cable 9121 OPTICAL DISK DIAGS ERROR - Focus Error - Check Cartridge, Drive, Adapter 9121 - Check Cable 9122 OPTICAL DISK DIAGS ERROR - Motor Sync Error - Cartridge upside down 9122 - Check Drive, Adapter, Cable 9123 OPTICAL DISK DIAGS ERROR - Write Fault - Check Drive, Adapter, or Cable 9124 OPTICAL DISK DIAGS ERROR - General Drive Error - Check Drive, Adapter 9124 - Check Cable 9125 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter 9125 - Check Cable 9126 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Drive, Adapter, Cable 9127 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter 9127 - Check Cable 9128 OPTICAL DISK DIAGS ERROR - Disk Not Initialized - Check Drive, Adapter 9128 - Check Cable 9129 OPTICAL DISK DIAGS ERROR - Disk ID Did Not Match - Check Drive, Adapter 9129 - Check Cable 9130 OPTICAL DISK DIAGS ERROR - Read-Only Disk Installed - Check Disk 9130 - Check Drive, Adapter 9130 - Check Cable 9131 OPTICAL DISK DIAGS ERROR - No Disk Present - Check Disk 9131 - Check Drive, Adapter, Cable 9132 OPTICAL DISK DIAGS ERROR - Illegal Disk Detected - Check Disk 9132 - Check Adapter, Drive 9132 - Check Cable 9133 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Check Drive, Adapter 9133 - Check Cable 9134 OPTICAL DISK DIAGS ERROR - Read-Only Disk Detected - Check Drive, Adapter 9134 - Check Cable 9135 OPTICAL DISK DIAGS ERROR - Illegal Disk Detected - Check Drive, Adapter 9135 - Check Cable 9136 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Adapter, Drive 9136 - Check Cable 9138 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry test again 9138 - Check Drive, Adapter 9138 - Check Cable 9141 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry tests 9141 - Check Drive, Adapter 9141 - Check Cable 9144 OPTICAL DISK DIAGS ERROR - WRITE-PROTECT Window Not Opened - Retry tests 9144 - Check Drive 9144 - Check Adapter 9144 - Check Cable 9145 OPTICAL DISK DIAGS ERROR - No Disk Change Detected - Retry tests 9145 - Check Drive, Adapter 9145 - Check Cable 9146 OPTICAL DISK DIAGS ERROR - WRITE-PROTECT Window Not Closed - Retry tests 9146 - Check Drive 9146 - Check Adapter 9146 - Check Cable 9148 OPTICAL DISK DIAGS ERROR - Adapter Card - Check Adapter, Drive, or Cable 9150 OPTICAL DISK DIAGS ERROR - Seek Command Failed - Check Drive, Adapter 9150 - Check Cable 9151 OPTICAL DISK DIAGS ERROR - Not At Track Zero - Check Drive, Adapter 9151 - Check Cable 9152 OPTICAL DISK DIAGS ERROR - Track Address Error - Check Drive, Adapter 9152 - Check Cable 9153 OPTICAL DISK DIAGS ERROR - Not At Track 17099 - Check Drive, Adapter 9153 - Check Cable 9154 OPTICAL DISK DIAGS ERROR - Track Address Error - Check Drive, Adapter 9154 - Check Cable 9155 OPTICAL DISK DIAGS ERROR - Track Address 17K Not Found - Check Drive 9155 - Check Adapter 9155 - Check Cable 9156 OPTICAL DISK DIAGS ERROR - Seek Time Too Long - Check Drive, Adapter 9156 - Check Cable 9157 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter 9157 - Check Cable 9158 OPTICAL DISK DIAGS ERROR - No Data Read Error Found - Check Drive, Adapter 9158 - Check Cable 9159 OPTICAL DISK DIAGS ERROR - No Null Sector Found - Check Drive, Adapter 9159 - Check Cable 9160 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter 9160 - Check Cable 9161 OPTICAL DISK DIAGS ERROR - Write Command Failed - Check Drive, Adapter 9161 - Check Cable 9162 OPTICAL DISK DIAGS ERROR - Data Compare Error - Check Drive, Adapter 9162 - Check Cable 9163 OPTICAL DISK DIAGS ERROR - Read Verify Error - Check Drive, Adapter 9163 - Check Cable 9164 OPTICAL DISK DIAGS ERROR - Demark Verify Failed - Check Drive, Adapter 9164 - Check Cable 9165 OPTICAL DISK DIAGS ERROR - Demark Bit Not Set - Check Drive, Adapter 9165 - Check Cable 9166 OPTICAL DISK DIAGS ERROR - Seek 1/3 Timing Error - Check Drive, Adapter 9166 - Check Cable 9167 OPTICAL DISK DIAGS ERROR - Seek 2/3 Timing Error - Check Drive, Adapter 9167 - Check Cable 9168 OPTICAL DISK DIAGS ERROR - Seek 3/3 Timing Error - Check Drive, Adapter 9168 - Check Cable 9170 OPTICAL DISK DIAGS ERROR - Seek Error Set - Check Drive, Adapter, Cable 9171 OPTICAL DISK DIAGS ERROR - Controller RAM/ROM Error - Check Drive, Adapter 9171 - Check Cable 9172 OPTICAL DISK DIAGS ERROR - Demark Function Error - Check Drive, Adapter 9172 - Check Cable 9173 OPTICAL DISK DIAGS ERROR - Detected Error Set - Check Drive, Adapter 9173 - Check Cable 9174 OPTICAL DISK DIAGS ERROR - Modulator/Demodulator Error - Check Drive 9174 - Check Adapter 9174 - Check Cable 9175 OPTICAL DISK DIAGS ERROR - Invalid Command - Check Adapter, Drive, Cable 9176 OPTICAL DISK DIAGS ERROR - Illegal Disk Error - Check Adapter, Drive, Cable 9177 OPTICAL DISK DIAGS ERROR - Both drives set to same address or wrong address 9178 OPTICAL DISK DIAGS ERROR - ID Mismatch - Check Drive, Adapter, or Cable 9179 OPTICAL DISK DIAGS ERROR - Sector Not Found - Check Drive, Adapter, Cable 9181 OPTICAL DISK DIAGS ERROR - Sense Command Failed - Check Drive, Adapter 9181 - Check Cable 9182 OPTICAL DISK DIAGS ERROR - Read Command Error - Check Drive, Adapter, Cable 9185 OPTICAL DISK DIAGS ERROR - Diagnostic Track Error - Check Drive, Adapter 9185 - Check Cable 9186 OPTICAL DISK DIAGS ERROR - Diagnostic Demark Error - Check Drive, Adapter 9186 - Check Cable 9187 OPTICAL DISK DIAGS ERROR - No Demark Bit Set - Check Drive, Adapter, Cable 9198 OPTICAL DISK DIAGS ERROR - Invalid Command - Re-IPL CPU with ON/OFF switch ~~~~~ TITLE: 100XX MULTI PROTOCOL ADAPTER ERRORS.................1023 10001 DIAGS Error - Cannot detect presence of Multiprotocol adapter 10002 DIAGS Error - Card selected feedback error 10003 DIAGS Error - Port 102H failed register test 10004 DIAGS Error - Port 103H failed register test 10006 DIAGS Error - Serial option cannot be put to sleep 10007 DIAGS Error - Cable error 10008 DIAGS Error - Async IRQ3 Error 10009 DIAGS Error - Async IRQ4 Error 10010 DIAGS Error - 16550 fails register test 10011 DIAGS Error - Internal wrap test of 16550 modem control lines failed 10012 DIAGS Error - External wrap test of 16550 modem control lines failed 10013 DIAGS Error - 16550 transmit error 10014 DIAGS Error - 16550 receive error 10015 DIAGS Error - 16550 receive data not equal transmit data 10016 DIAGS Error - 16550 interrupt function error 10017 DIAGS Error - 16550 failed baud rate test 10018 DIAGS Error - 16550 interrupt driven receive wrap failed 10019 DIAGS Error - 16550 FIFO error 10026 DIAGS Error - 8255 Port A error 10027 DIAGS Error - 8255 Port B error 10028 DIAGS Error - 8255 Port C error 10029 DIAGS Error - 8254 timer 0 error 10030 DIAGS Error - 8254 timer 1 error 10031 DIAGS Error - 8254 timer 2 error 10032 DIAGS Error - Bisync DSR response to DTR error 10033 DIAGS Error - Bisync CTS response to RTS error 10034 DIAGS Error - 8251 hardware reset test failed 10035 DIAGS Error - 8251 function error 10035 DIAGS Error - 8251 internal software rest failure 10035 DIAGS Error - 8251 error reset command failed 10035 DIAGS Error - 8251 cannot detect overrun error 10036 DIAGS Error - 8251 Status error 10036 DIAGS Error - 8251 Tx ready error 10036 DIAGS Error - 8251 Rx ready error 10037 DIAGS Error - Bisync timer interrupt error 10038 DIAGS Error - Bisync transmit interrupt error 10039 DIAGS Error - Bisync receive interrupt error 10040 DIAGS Error - Stray IRQ3 error 10041 DIAGS Error - Stray IRQ4 error 10042 DIAGS Error - Bisync external wrap error 10044 DIAGS Error - Bisync data wrap error 10045 DIAGS Error - Bisync line status/condition error 10046 DIAGS Error - Bisync timeout error during data wrap test 10050 DIAGS Error - 8273 command acceptance or results ready timeout error 10051 DIAGS Error - 8273 PORT A error 10052 DIAGS Error - 8273 PORT B error 10053 DIAGS Error - SDLC modem status change logic error 10054 DIAGS Error - SDLC timer interrupt (IRQ4) error 10055 DIAGS Error - SDLC modem status change interrupt (IRQ4) error 10056 DIAGS Error - SDLC external wrap error 10057 DIAGS Error - SDLC interrupt results error 10058 DIAGS Error - SDLC data wrap error 10059 DIAGS Error - SDLC transmit interrupt error 10060 DIAGS Error - SDLC receive interrupt error 10061 DIAGS Error - DMA channel 1 error (transmit) 10062 DIAGS Error - DMA channel 1 error (receive) 10063 DIAGS Error - 8273 status detect error 10064 DIAGS Error - 8273 error detect failure ~~~~~ TITLE: 101XX 300/1220 MODEM ADAPTER ERRORS................1024 10101 DIAGS Error - Cannot detect presence of modem 10102 DIAGS Error - Card selected feedback error 10103 DIAGS Error - Port 102H failed register test 10106 DIAGS Error - Serial option cannot be put to sleep 10108 DIAGS Error - Async IRQ3 Error 10109 DIAGS Error - Async IRQ4 Error 10110 DIAGS Error - 16550 fails register test 10111 DIAGS Error - Internal wrap test of 16550 modem control lines failed 10113 DIAGS Error - 16550 transmit error 10114 DIAGS Error - 16550 receive error 10115 DIAGS Error - 16550 receive data not equal transmit data 10116 DIAGS Error - 16550 interrupt function error 10117 DIAGS Error - 16550 failed baud rate test 10125 DIAGS Error - Modem reset result code error 10126 DIAGS Error - Modem general result code error 10127 DIAGS Error - Modem S registers write/read error 10128 DIAGS Error - Modem turn echo on/off error 10129 DIAGS Error - Modem enable/disable result codes error 10130 DIAGS Error - Modem enable number/word result code error 10133 DIAGS Error - Connect results for 300 baud not received 10134 DIAGS Error - Connect results for 1200 baud not received 10135 DIAGS Error - Modem failed local analog loop test at 300 baud 10136 DIAGS Error - Modem failed local analog loop test at 1200 baud 10137 DIAGS Error - Modem does not respond to escape/reset sequence 10138 DIAGS Error - S reg 13 does not reflect correct parity or data bits 10139 DIAGS Error - S reg 15 does not reflect correct bit rate ~~~~~ TITLE: 102XX 4250 PRINT ADAPTER/A ERRORS...................1025 102XX 4250 Print Adapter failure ~~~~~ TITLE: 104XX ESDI DRIVES AND ADAPTERS ERRORS...............1026 10440 8550-021 60 Meg ESDI Adapter Error. 10441 8550-021 60 Meg ESDI Adapter Error. 10442 8550-021 60 Meg ESDI Adapter Error. 10443 8550-021 60 Meg ESDI Adapter Error. 10444 8550-021 60 Meg ESDI Adapter Error. 10445 8550-021 60 Meg ESDI Adapter Error. 10446 8550-021 60 Meg ESDI Adapter Error. 10447 8550-021 60 Meg ESDI Adapter Error. 10450 DIAGS Error - Replace drive (read write test failed) 10451 DIAGS Error - Replace drive (read verify test failed) 10452 DIAGS Error - Replace drive (seek test failed) 10453 DIAGS Error - Replace drive (wrong drive type indicated) 10454 DIAGS Error - Controller (controller test failed sector buffer test) 10455 DIAGS Error - Controller (controller failure, invalid failure) 10456 DIAGS Error - Controller (diag command failure) 10457 DIAGS Error - Repl. drive (integrated controller test failure) 10458 DIAGS Error - Repl. drive (integrated controller test failure) 10458 DIAGS Error - If 8570-121 or 8570-A21 see ECA020 10459 DIAGS Error - Replace drive (diag command failure) 10460 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10461 DIAGS Error - Drive fromat error 10462 DIAGS Error - Controller (head select error) 10463 DIAGS Error - Drive (read/write sector error) 10464 DIAGS Error - Drive (primary map unreadable) 10465 DIAGS Error - Controller (ECC 8 bit error) 10466 DIAGS Error - Controller (ECC 9 bit error) 10467 DIAGS Error - Drive (soft seek error) 10468 DIAGS Error - Drive (hard seek error) 10469 DIAGS Error - Drive (drive soft error count execeeded) 10470 DIAGS Error - Controller (attachment diag error) 10471 DIAGS Error - Controller (wrap mode interface error) 10472 DIAGS Error - Controller (wrap mode drive selected error) 10473 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10474 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10475 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10476 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10477 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10478 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10479 DIAGS Error - Unknown. Repl. drive, then controller, then system board 10480 POST Error - Replace disk "C" (seek failure) 10480 DIAGS Error - Controller (com/data-attn bad) 10481 POST Error - Replace disk "D" (seek failure) 10481 DIAGS Error - Controller (xfr req-ready bad) 10482 POST Error - Replace controller (failed controller test) 10482 DIAGS Error - Controller (drvsell-xfr ack bad) 10483 POST Error - Replace controller (failed reset) 10483 POST Error - If 8570-121 or 8570-A21 see ECA020 10483 DIAGS Error - Controller (drvse10-config/stat bad) 10484 DIAGS Error - Controller (hdse13-selected bad) 10485 DIAGS Error - Controller (hdse12-selected bad) 10486 DIAGS Error - Controller (hdse11-selected bad) 10487 DIAGS Error - Controller (hdse10-selected bad) 10488 DIAGS Error - Controller (rg - cmd cmplt 2) 10489 DIAGS Error - Controller (wg - cmd cmplt 1) 10490 POST Error - Replace disk "C" (read failure) 10490 DIAGS Error - Controller (drive connected no test done) 10491 POST Error - Replace disk "D" (read failure) 10499 DIAGS Error - Controller Failure ~~~~~ TITLE: 107XX 5.25" 1.2MB EXTERNAL DISKETTE DRIVE ERRORS....1027 10701 Post Error Replace Adapter 10759 Write-protect error ~~~~~ TITLE: 119XX 3119 SCANNER AND ADAPTER ERRORS...............1028 11944 3119 Adapter Error Replace Adapter 11945 3119 Possible Power Supply or Lamp Problem. 11950 3119 Lamp or Optics Problem. 11952 3119 Lamp or Optics Problem. 11953 3119 Lamp or Optics Problem. 11954 3119 Lamp or Optics Problem. 11957 3119 Possible Optics problem or 3119 Adapter Problem. 11958 3119 Possible Optics Problem or 3119 Adapter Problem. ~~~~~ TITLE: 129XX PROCESSOR CARD ERRORS.........................1029 12901 Failed processor portion of processor board test 12902 Failed cache portion of processor board test 12904 Second level cache error 12905 Second level cache warning 12906 Second level cache warning 12907 Second level cache fatal error 12908 Second level cache POST error ~~~~~ TITLE: 149XX PLASMA DISPLAY ADAPTER ERRORS.................1030 14901 Replace Plasma Display Adapter, System Board, or Plasma Display 14902 Replace Plasma Display Adapter, System Board, or Plasma Display 14922 Replace Plasma Display Adapter, System Board, or Plasma Display 14932 Replace External Display, or Plasma Display Adapter ~~~~~ TITLE: 164XX 3.5" INTERNAL TAPE DRIVE ERRORS...............1031 16451 Not enough memory to operate the tape drive 16452 Cartridge presence error 16453 Servo electronics/mechanism failed 16454 The cartridge was not formatted, or read chain failed 16455 The EOT test failed 16456 The BOT test failed 16457 Track following error -- servo electronics/mechanism failed 16458 Internal software error 16459 Floppy disk controller failure 16460 Internal software error 16461 Unrecoverable read error -- drive failure 16462 Internal software error 16463 User changed the cartridge 16464 DMA controller failure 16465 General drive failure 16466 No internal tape drives were found 16467 Write protect switch failed 16468 Unrecoverable write error -- drive failure 16469 Defective cartridge ~~~~~ TITLE: 165XX 6157 TAPE ATTACHEMENT ADAPTER ERRORS.........1032 16520 6157 Tape Drive Error 16540 Adapter of Drive Error FRU Unknown ~~~~~ TITLE: 194XX 2-8MB 80286 MEMORY EXPANSION ADAPTER ERRORS...1033 194XX 2-8MB 80286 Memory Expansion Adapter ~~~~~ TITLE: I999 IML ERRORS (Model 90 & 95)...................1034 I999 Invalid, incompatible or unreadable disk IML record Boot from Reference Diskette and recreate System Partition ~~~~~